Magnet bonding for small motors must guarantee reliable fixing strength while satisfying the demands of automated production efficiency. For micro motors and small brushless motors that need shortened heat curing time, ELAPLUS EP 1772‑1K, a one‑component epoxy magnet adhesive, can be evaluated. It is paste‑form, with two reference curing conditions specified on the datasheet: 220°C / 20 s and 150°C / 20 min, suitable for fast curing process verification.

Small permanent magnet motors are widely used in smart home appliances, power tools, automotive auxiliary motors and industrial automation equipment. Such motors generally feature compact size, tight structure and large batch output. For products adopting adhesive to fix magnets, manufacturers pay attention not only to bonding reliability, but also to curing time, equipment configuration and assembly takt.
EP 1772‑1K is a one‑component epoxy adhesive designated for high‑frequency curing of magnet segments.

| Performance Item | EP 1772‑1K |
|---|---|
| Product Type | One‑component epoxy adhesive |
| Adhesive Form | Paste |
| Density | 1.45 g/cm³ |
| Reference Cure Condition 1 | 220°C / 20 s |
| Reference Cure Condition 2 | 150°C / 20 min |
| Hardness | Shore D 85 |
| Shear Strength | 18 MPa |
| Tg | 120°C |
| Marked Service Temperature | -50 ~ 200°C |
The above fast curing conditions are quoted from the datasheet. Before formal mass production introduction, it is necessary to confirm the heating method, actual temperature of adhesive layer, magnet plating and heat resistance of other motor parts.
In particular, the condition of 220°C / 20 s shall not be simply understood as full curing of motor components of any size merely by heating in an oven for 20 seconds.
In small motor manufacturing, magnet bonding normally includes dispensing, assembly, positioning, curing and inspection. If the curing cycle is too long, the production line has to be equipped with more jigs and buffer areas.
Fast curing process serves as a method to optimise takt time, yet the actual benefit depends on equipment heating rate, thermal capacity of components and curing quality.
Featuring high‑temperature fast curing, EP 1772‑1K can be assessed for short‑time thermal curing schemes. For magnets and rotor structures capable of withstanding corresponding temperature, process tests can be carried out to verify local heating, induction heating and other thermal curing approaches.
| Model | Cure Condition | Main Selection Direction |
|---|---|---|
| EP 1739‑1K | 90°C / 30 min | Medium‑temperature curing |
| EP 1769‑1K | 120°C / 30 min | High viscosity, high Tg requirement |
| EP 2029‑2K | 100°C / 60 min | Two‑component, high‑temperature bonding performance evaluation |
| EP 1772‑1K | 220°C / 20 s or 150°C / 20 min | Fast curing for small motors |
Do not select adhesives only by comparing curing speed. Magnet plating, rotor structure, bond line thickness and actual bonding strength also need to be considered.
Typical applicable candidates: Micro brushless motors, small fan motors, smart home appliance motors, power tool motors, automotive auxiliary drive motors, small industrial permanent magnet motors.
The above are material selection references. Final applicability shall be confirmed according to specific motor design and verification results.
Key recommended verification contents:
Q1: Can magnet adhesive for small motors realise fast curing? Fast thermal‑cure epoxy adhesive is available for selection, but the actual temperature and cure degree of adhesive layer must be confirmed.
Q2: Is EP 1772‑1K suitable for automated dispensing? It can be taken as a candidate for automated dispensing process. Dispensing stability, needle adaptability and dispensing precision need to be verified on site.
Q3: Does fast curing mean higher bonding strength? It does not. Curing speed and final bonding strength are two different indicators and shall be verified separately.
Magnet bonding of small motors requires balance between structural reliability and production efficiency.
ELAPLUS EP 1772‑1K one‑component epoxy adhesive supports fast high‑temperature curing for magnet fixation of small motors and automated production process evaluation, helping manufacturers explore more efficient magnet bonding solutions.
COPYRIGHT ◎ 2023 Elaplus Functional Materials Co. LTD
We will reply within 24 working hours. If urgent, please help us to contact through email: kennis.zhu@elaplus.cc